manualshive.com logo in svg

Thermo Scientific 42iQTL, Instruction Manual

Share
Download
Thermo Scientific 42iQTL Instruction Manual Download Page 51

Operation 

Calibration 

Thermo Scientific 

42iQTL Instruction Manual     

3-25

 

Home Screen>Calibration>Advanced Calibration>Manual 
Calibration>Adjust Backgrounds>Adjust Prereactor Background 

 

The Adjust NO, NO

x

, and Prereactor Background screens contains the 

following information: 

●

 

Adjust NO Background: 

User manually adjusts zero NO background. 

●

 

Adjusted NO Concentration: 

Read only. Displays what the NO 

concentration value will become when the calibrate button is pressed. 

●

 

Current NO Concentration: 

Read only. Displays the current NO 

concentration. 

●

 

Adjust NO

x

 Background: 

User manually adjusts zero NO

x

 background. 

●

 

Adjusted NO

x

 Concentration: 

Read only. Displays what the NO

x

 

concentration value will become when the calibrate button is pressed. 

●

 

Current NO

x

 Concentration: 

Read only. Displays the current NO

x

 

concentration. 

●

 

Adjust Prereactor Background: 

User manually adjusts zero Prereactor 

background. 

●

 

Adjusted Prereactor Concentration: 

Read only. Displays what the 

Prereactor concentration value will become when the calibrate button is 
pressed. 

●

 

Current Prereactor Concentration: 

Read only. Displays the current 

Prereactor concentration. 

●

 

Calibrate: 

When pressed, updates the background. 

 

Summary of Contents for 42iQTL























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands