manualshive.com logo in svg

Thermo Scientific 42iQTL, Instruction Manual

Share
Download
Thermo Scientific 42iQTL Instruction Manual Download Page 112

Operation 

Settings 

3-86

     42iQTL Instruction Manual 

Thermo Scientific 

●

 

Down: 

●

 

Manual Entry: 

Shows current value. If the PMT supply cell is 

pressed, user can manually change the value. 

●

 

Target Concentration: 

Displays target concentration. If target 

concentration cell is pressed, user can enter target concentration. 

●

 

Calibration Concentration: 

Displays calibration concentration. 

●

 

Auto Calibration: 

When pressed, the auto-calibration process is 

initiated. Please allow up to 5 minutes for calibration to complete. 
PMT voltage is automatically adjusted until calibration 
concentration is with 1% of target concentration. 

●

 

End Calibration: 

When pressed, the auto calibration is interrupted 

and the value does not change. 

●

 

Default PMT Supply: 

When pressed, the default PMT supply value 

is saved. 

 

Summary of Contents for 42iQTL























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands