manualshive.com logo in svg

Thermo Scientific 42iQTL, Instruction Manual

Share
Download
Thermo Scientific 42iQTL Instruction Manual Download Page 74

Operation 

Settings 

3-48

     42iQTL Instruction Manual 

Thermo Scientific 

●

 

Chamber Temp Sensor Open:

 Displays OK/Fail for chamber 

temperature sensor open. 

●

 

Cooler Temperature:

 Displays OK/Fail for cooler temperature. User 

can adjust low and high alarm limits. 

●

 

Cooler Temp Sensor Short:

 Displays OK/Fail for cooler temperature 

sensor short. 

●

 

Cooler Temp Sensor Open:

 Displays OK/Fail for cooler temperature 

sensor open. 

●

 

Cooler Current:

 Displays the cooler current reading. 

●

 

Cooler Current too Low:

 Displays OK/Fail for cooler current too 

low. 

●

 

Cooler Current too High:

 Displays OK/Fail for cooler current too 

high. 

●

 

Cooler Voltage:

 Displays the current cooler voltage reading. 

●

 

Cooler Voltage too Low:

 Displays OK/Fail for cooler voltage too low. 

●

 

Cooler Voltage too High:

 Displays OK/Fail for cooler voltage too 

high. 

●

 

PMT Voltage:

 Displays the current PMT voltage reading. 

●

 

PMT Voltage too Low:

 Displays OK/Fail for PMT voltage too low. 

●

 

PMT Voltage too High:

 Displays OK/Fail for PMT voltage too 

high. 

●

 

Frequency:

 Displays the current frequency reading. 

●

 

Frequency too Low:

 Displays OK/Fail for frequency too low. 

●

 

Frequency too High:

 Displays OK/Fail for frequency too high. 

●

 

Low Gain:

 Displays the current low gain reading. 

●

 

Gain:

 Displays the current gain reading. 

●

 

Board Communication:

 Displays OK/Fail for board communication 

status. 

●

 

Power Supply:

 Displays OK/Fail of power supplies. Power supply 

goes red if any voltages are outside their limits. No voltage rows 
ever get highlighted. 

●

 

3.3 V Diagnostic:

 Displays current voltage readings. Alarm 

limits are not changeable. 

●

 

5 V Diagnostic:

 Displays current voltage readings. Alarm limits 

are not changeable. 

Summary of Contents for 42iQTL























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands