Thermo Scientific 42iQTL Instruction Manual Download Page 149

Page: 149 / 310

Operation

Settings

Thermo Scientific

42iQTL Instruction Manual

3-123

The USB Drive screen allows the user to update firmware,
download/upload information, and change the USB password.

Note

The USB drive screen only is useable when a USB drive is inserted

into the USB port. When a USB drive is inserted, the user is prompted to
enter the password if a password has been set.

▲

Home Screen>Settings>USB Drive

The USB Drive screen contains the following information:

●

Firmware Update Via USB Drive:

If USB is mounted, user can update

instrument firmware.

●

Download Data To USB Drive:

User can download/upload

information.

●

Change USB Password:

User can change the USB password.

USB Drive

Summary of Contents for 42iQTL























































































































































































































































































































Search results

Summary of Contents for 42iQTL

Reviews:

Brands by name

Popular brands

Thermo Scientific 42iQTL, Instruction Manual

Search results

Summary of Contents for 42iQTL

Reviews:

Brands by name

Popular brands