manualshive.com logo in svg

Thermo Scientific 42iQTL, Instruction Manual

Share
Download
Thermo Scientific 42iQTL Instruction Manual Download Page 128

Operation 

Settings 

3-102

     42iQTL Instruction Manual 

Thermo Scientific 

 

The Instrument Setpoints screen allows the user to view and set all settable 
instrument minimum and maximum values. 

Use the 

 and 

 buttons to move up and down and the 

 and 

 

buttons to move left and right. 

Home Screen>Settings>Instrument Settings>Instrument Setpoints

 

 

The Alarm Setpoints screen contains the following information: 

●

 

Across: 

●

 

Variable: 

Lists the items that have settable alarm limits. 

●

 

Setpoint: 

User sets high alarm for item. 

●

 

Units: 

Units for each item (not settable). 

●

 

Down: 

●

 

NO

2

 Converter Temperature: 

NO

2

 converter temperature. 

 

Instrument Setpoints

Summary of Contents for 42iQTL























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands