manualshive.com logo in svg

Thermo Scientific 42iQTL, Instruction Manual

Share
Download
Thermo Scientific 42iQTL Instruction Manual Download Page 72

Operation 

Settings 

3-46

     42iQTL Instruction Manual 

Thermo Scientific 

●

 

Prereactor Bkg Check Offset:

 Displays prereactor concentration based 

on the last attempted background calibration. High alarm shows 
user defined limit for acceptable background check offset. 

●

 

NO Bkg Check Offset:

 Displays NO concentration based on the last 

attempted background calibration. High alarm shows user defined 
limit for acceptable background check offset. 

●

 

NO

x

 Bkg Check Offset:

 Displays NO

x

 concentration based on the 

last attempted background calibration. High alarm shows user 
defined limit for acceptable background check offset. 

●

 

NO Span Check Offset:

 Displays NO concentration based on the 

last attempted span calibration. High alarm shows user defined 
limit for acceptable span check offset (compared to the span 
concentration value). Span concentration shows span setpoint. 

●

 

NO

x

 Span Check Offset:

 Displays NO

x

 concentration based on the 

last attempted span calibration. High alarm shows user defined 
limit for acceptable span check offset (compared to the span 
concentration value). Span concentration shows span setpoint. 

Note  

If both the low alarm and high alarms are set to zero, then no alarm 

will show. 

▲

  

Summary of Contents for 42iQTL























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands