manualshive.com logo in svg

Thermo Scientific 42iQTL, Instruction Manual

Share
Download
Thermo Scientific 42iQTL Instruction Manual Download Page 181

Calibration 

Calibration in Dual Range and Auto Range Mode 

Thermo Scientific 

42iQTL Instruction Manual     

4-19

 

3.

 

When the responses stabilize, from the Home screen, choose 

Calibration>Calibrate Span Coefficients>Calibrate Low Range NO 
Span Coefficient

. 

The user sets the span concentration by pressing the Edit Span 
Concentration button. The Calculated Low Range NO Span 
Coefficient button will show what the span coefficient will be set to if 
the Calibrate button is pressed. 

4.

 

Enter the NO calibration gas concentration using the pushbuttons, and 
then press 

Calibrate

 to calculate and save the new low range NO span 

coefficient based on the entered span coefficient. 

Use the following procedure to calibrate the NO

x

 channel to the NO

x

 

calibration gas. 

1.

 

Press the Back button to return to the Calibration menu and choose 

Calibrate Low Range NO

x

 Span Coefficient

. 

The user sets the span concentration by pressing the Edit Span 
Concentration button. The Calculated Low Range NO

x

 Span 

Coefficient button will show what the span coefficient will be set to if 
the Calibrate button is pressed. 

2.

 

Verify that the low NO

x

 calibration gas concentration is the same as the 

low NO calibration gas concentration plus any known NO

2

 impurity. 

3.

 

Enter the NO

x

 calibration gas concentration using the pushbuttons, 

and then press 

Calibrate

 to calculate and save the new low range NO

x

 

span coefficient based on the entered span coefficient. 

Use the following procedure to calibrate the NO

2

 channel to the NO

2

 

calibration gas. 

1.

 

Adjust the O

3

 generator in the GPT system to generate sufficient O

3

 to 

produce a decrease in the low NO concentration equivalent to about 
80% of the URL of the low NO

2

 range. The decrease must not exceed 

90% of the low NO concentration determined in the “

Calibrate NOx 

Low

” procedure. 

2.

 

Press the Back button to return to the Calibration menu and choose 

Calibrate Low Range NO

2

 Span Coefficient

. 

Calibrate NO

x 

Low

Calibrate NO

2 

Low

Summary of Contents for 42iQTL























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands