manualshive.com logo in svg

Thermo Scientific 42iQTL, Instruction Manual

Share
Download
Thermo Scientific 42iQTL Instruction Manual Download Page 285

 

Thermo Scientific 

42iQTL Instruction Manual     

A-1

 

Appendix A

 

 

Safety, Warranty, and WEEE 

 

Review the following information carefully before using the instrument. 
This manual provides specific information on how to operate the 
instrument, however if the instrument is used in a manner not specified by 
the manufacturer, the protection provided by the equipment may be 
impaired. 

This manual contains important information to alert you to potential safety 
hazards and risks of equipment damage. Refer to the following types of 
alerts you may see in this manual. 

Safety and Equipment Damage Alert Descriptions 

Alert 

Description 

 

A hazard is present that will result in death or serious 
personal injury if the warning is ignored.  

▲

  

 

A hazard is present or an unsafe practice can result in 
serious personal injury if the warning is ignored.  

▲

  

 

The hazard or unsafe practice could result in minor to 
moderate personal injury if the warning is ignored.  

▲

  

            Equipment Damage 

The hazard or unsafe practice could result in property 
damage if the warning is ignored.  

▲

  

Safety and Equipment Damage Alerts in this Manual 

 

Alert 

Description 

 

If the equipment is operated in a manner not specified by 
the manufacturer, the protection provided by the equipment 
may be impaired.  

▲

  

 

The service procedures in this manual are restricted to 
qualified service personnel only.  

▲

  

             Equipment Damage 

Do not attempt to lift the analyzer by the cover or other 
external fittings.  

▲

  

 

This adjustment should only be performed by an instrument 
service technician.  

▲

  

Safety

Safety and

Equipment Damage 

Alerts

 

 

 

 

Summary of Contents for 42iQTL























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands