manualshive.com logo in svg

Thermo Scientific 42iQTL, Instruction Manual

Share
Download
Thermo Scientific 42iQTL Instruction Manual Download Page 122

Operation 

Settings 

3-96

     42iQTL Instruction Manual 

Thermo Scientific 

 

The Digital I/O screen allows for configuring the digital inputs/outputs. 
This is only visible if selected in Settings>Configuration>

Digital I/O

. 

Home Screen>Settings>Communications>Digital I/O

 

 

The Digital I/O screen contains the following information: 

●

 

Digital In: 

Allows the user to view digital inputs from external devices. 

●

 

Digital Out (Relays): 

Allows the user to view relay outputs. 

●

 

Digital Out (Solenoids): 

Allows the user to view solenoid outputs. 

●

 

Advanced Digital I/O: 

Allows user to test the digital out relays and 

solenoids. 

 

Digital I/O

Summary of Contents for 42iQTL























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands