manualshive.com logo in svg

Thermo Scientific 42iQTL, Instruction Manual

Share
Download
Thermo Scientific 42iQTL Instruction Manual Download Page 233

Servicing 

DMC PMT Cooler and Reaction Chamber Replacement 

Thermo Scientific 

42iQTL Instruction Manual     

7-29

 

 

Use the following procedure to replace the PMT cooler and clean or 
replace the reaction chamber assembly. 

●

 

Remove the PMT Cooler 

●

 

Replacing the PMT board 

●

 

Removing and Cleaning the Reaction chamber 

●

 

Replacing the PMT Cooler and Reaction chamber 

●

 

PMT Replacement 

Use the following procedure to remove the PMT cooler from the 
instrument. 

Equipment Required: 

Phillips drive, #2 

1.

 

Turn the instrument OFF, unplug the power cord, and remove the 
cover (

Figure 2–1

). 

Make sure the PMT has cooled down before touching. 

▲

  

 

2.

 

Unhook plumbing by pulling loop downwards and unhook tubing. 

3.

 

Using a #2 Phillips drive, unfasten two 6-32 flat head screws. 

4.

 

Pull shroud outwards. 

DMC PMT Cooler

and Reaction

Chamber

Replacement

PMT Cooler Shroud

Removal

Icon Here

Summary of Contents for 42iQTL























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands