manualshive.com logo in svg

Thermo Scientific 42iQTL, Instruction Manual

Share
Download
Thermo Scientific 42iQTL Instruction Manual Download Page 195

Maintenance 

Pump Rebuilding 

Thermo Scientific 

42iQTL Instruction Manual     

5-5

 

 

Use the following procedure to rebuild the pump. 

Equipment required: 

Pump rebuild kit (qty. 2) 

Allen wrench, 3 mm and 4 mm 

Wrench, 9/16-inch 

Needlenose pliers 

1.

 

Turn instrument off, unplug the power cord, and disconnect the pump 
plumbing from the instrument. 

2.

 

Note the orientation of the pump head top plate for later reassembly. 
Using a 3 mm Allen wrench, remove the eight socket head screws and 
washers securing the pump head top plate. 

3.

 

Discard the old PTFE gasket. 

4.

 

Note the orientation of the diaphragm head for later reassembly. 
Remove the diaphragm head. Using a 4 mm Allen wrench, remove the 
four socket head screws securing the diaphragm head to the pump 
body. 

5.

 

Insert the tips of blunt needlenose pliers in the dimples of the clamping 
disk, then loosen and remove the clamping disk. 

6.

 

Remove and discard the old PTFE gasket. 

7.

 

Insert the clamping disk into the new Teflon diaphragm (three pieces) 
and screw the clamping disk into the pump. Do not over tighten. 

Pump Rebuilding

Summary of Contents for 42iQTL























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands