manualshive.com logo in svg

Thermo Scientific 42iQTL, Instruction Manual

Share
Download
Thermo Scientific 42iQTL Instruction Manual Download Page 199

 

Thermo Scientific 

42iQTL Instruction Manual    

6-1

 

Chapter 6

 

 

Troubleshooting 

The troubleshooting guide presented in this chapter is designed to help 
isolate and identify instrument problems. 

Read the safety precautions in Appendix A, “

Safety

” before performing any 

actions listed in this chapter. 

Table 6–1

 provides general troubleshooting information for the common 

platform and indicates the checks that you should perform if you 
experience an instrument problem. It also lists 42iQTL specific 
troubleshooting information and alarm messages you may see on the 
graphics display and provides recommendations about how to resolve the 
alarm condition. 

Table 6–1.

 42iQTL Troubleshooting Guide 

Problem 

Possible Cause 

Action 

Instrument does not start 
(LEDs on front panel do not 
come on and display is 
blank) 

No power 

Verify that the power cord is 
plugged in, power is available and 
that it matches the voltage and 
frequency configuration of the 
instrument. 

 

Fuse is blown or 
missing 

Disconnect power and check fuses 
with a volt meter. 

 

Bad switch or wiring 
connection to switch 

Check for 24V @ J9 on the 
Backplane board (middle pins). 
Check all wiring connections. 

Front panel display does 
not start (LEDs on front 
panel are off) 

Disconnected ribbon 
cable 

Power down and evaluate 
connections of display ribbon 
cable. 

Front panel display does 
not start (LEDs on front 
panel are on) 

Defective Display 

Connect to the instrument using 
ePort. Select “Remote Interface”. If 
normal GUI is displayed, replace 
defective display. 

Front panel display stays 
white after power up (LEDs 
on front panel are on) 

Unseated or missing 
Micro SD card 

Power off, re-seat Micro SD or 
install if missing. 

Safety Precautions

Troubleshooting

Guide

Summary of Contents for 42iQTL























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands