manualshive.com logo in svg

Thermo Scientific 42iQTL, Instruction Manual

Share
Download
Thermo Scientific 42iQTL Instruction Manual Download Page 126

Operation 

Settings 

3-100

     42iQTL Instruction Manual 

Thermo Scientific 

 

The Instrument Settings screen allows the user to configure various 
instrument settings. 

Home Screen>Settings>Instrument Settings

 

 

Home Screen>Settings>Instrument Settings>More

 

 

The Instrument Settings screen contains the following information: 

●

 

Titlebar Setup: 

User chooses what concentration reading to display on 

the titlebar

.

 

●

 

Instrument Setpoints: 

View and set all available setpoints

.

 

●

 

Alarm Setpoints: 

View and set all available alarm minimum and 

maximum values. 

●

 

Ozonator Safety Enabled/Disabled: 

Enables/disables ozonator safety. 

●

 

PMT Supply Enabled/Disabled: 

Enables/disables PMT supply. 

●

 

Ozonator Supply Enabled/Disabled: 

Enables/disables ozonator supply. 

●

 

Display Setup: 

Sets touchscreen display settings

.

 

●

 

Clock: 

Sets date and time. 

Instrument Settings

Summary of Contents for 42iQTL























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands