manualshive.com logo in svg

Thermo Scientific 42iQTL, Instruction Manual

Share
Download
Thermo Scientific 42iQTL Instruction Manual Download Page 276

Optional Equipment 

Connecting External Devices 

9-10

     42iQTL Instruction Manual 

Thermo Scientific 

 

4.

 

There are six columns for each of the six available output channels: 

 

●

 

Output (V):

 Displays the actual output level at the terminal of the 

analog output board. For analog voltage, this value will default at the 
setting of the output channel, 1, 5, or 10 V. For analog current, this 
value will default at 20 mA. 

●

 

Decrease 



, 

Decrease

 



, 

and Decrease 

:

 Decreases the output by 

coarse, medium, or fine amounts. 

●

 

Increase 

, Increase 



, and 

Increase 



:

 Increases the output by 

coarse, medium, or fine amounts. 

●

 

Commit:

 Accepts the changes to the analog output levels. 

5.

 

For the desired analog output channel, increase or decrease the output 
until the reading on the recording device indicates the proper value. 

6.

 

After making changes to the output levels, the commit button will turn 
green. To accept the changes, press the Commit button. To revert to 
the previous values, press the back button to return to the previous 
analog output calibration screen. 

Summary of Contents for 42iQTL























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands