manualshive.com logo in svg

Thermo Scientific 42iQTL, Instruction Manual

Share
Download
Thermo Scientific 42iQTL Instruction Manual Download Page 188

Calibration 

Zero/Span Schedule 

4-26

     42iQTL Instruction Manual 

Thermo Scientific 

 

The Zero/Span Schedule is used to program the instrument to perform 
fully automated zero and span checks or adjustments. 

Home Screen>Calibration>Zero/Span Schedule 

 

Home Screen>Calibration>Zero/Span Schedule>More 

 

The Next Time button is used to view and set the initial date and time (24-
hour format) of the zero/span schedule. Once the zero/span schedule 
begins, the date and time of the next zero/span schedule is calculated and 
displayed.

 

The Period button defines the period or interval between zero/span 
schedule. Periods between 0 and 999 hours are acceptable. To turn the 
zero/span schedule off, set the period to 0. 

The Zero Duration button defines how long zero air is sampled by the 
instrument. The Span and Purge Duration buttons look and function the 
same way as the zero duration button. The span duration button is used to 
set how long the span gas is sampled by the instrument. The purge 
duration button is used to set how long the purge period will be after doing 

Zero/Span

Schedule

Next Time

Period

Zero/Span/Purge

Duration Minutes

Summary of Contents for 42iQTL























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands