manualshive.com logo in svg

Thermo Scientific 42iQTL, Instruction Manual

Share
Download
Thermo Scientific 42iQTL Instruction Manual Download Page 205

 

Thermo Scientific 

42iQTL Instruction Manual    

7-1

 

Chapter 7

 

 

Servicing 

This chapter describes the periodic servicing procedures that should be 
performed on the instrument to ensure proper operation and explains how 
to replace the 42iQTL subassemblies. 

Read the safety precautions before beginning any procedures in this 
chapter. 

The service procedures in this manual are restricted to qualified service 
representatives. 

▲

  

 

If the equipment is operated in a manner not specified by the 
manufacturer, the protection provided by the equipment may be 
impaired. 

▲

  

 

CAUTION  

If the LCD panel breaks, do not let the liquid crystal contact 

your skin or clothes. If the liquid crystal contacts your skin or clothes, wash 
immediately using soap and water. 

▲

  

Do not remove the LCD panel or frame from the LCD module. 

▲

  

The LCD polarizing plate is very fragile, handle it carefully. 

▲

  

Do not wipe the LCD polarizing plate with a dry cloth, as it may easily 
scratch the plate. 

▲

  

Do not use alcohol, acetone, MEK or other Ketone based or aromatic 
solvents to clean the LCD module, but rather use a soft cloth moistened 
with a naphtha cleaning solvent. 

▲

  

Do not place the LCD module near organic solvents or corrosive gases. 

▲

  

Do not shake or jolt the LCD module. 

▲

  

Safety 

Precautions

Icon Here

Icon Here

Summary of Contents for 42iQTL























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands