manualshive.com logo in svg

Thermo Scientific 42iQTL, Instruction Manual

Share
Download
Thermo Scientific 42iQTL Instruction Manual Download Page 158

Operation 

Settings 

3-132

     42iQTL Instruction Manual 

Thermo Scientific 

 

 

 

The Change USB Password screens contain the following information: 

●

 

Enter Current USB Password:

 User enters current USB password. 

●

 

Continue:

 Proceeds to next screen. 

●

 

Enter New USB Password:

 User enters new USB password. 

●

 

Confirm New Security Access Password:

 User confirms new security 

password for spelling confirmation. 

●

 

Commit New USB Password Change:

 Commits new USB password. 

●

 

Cancel and Return to the Home Screen:

 Exits screen and returns to the 

Home Screen without changing password. 

 

Summary of Contents for 42iQTL























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands