manualshive.com logo in svg

Texas Instruments TMS320C6201, Reference Manual

The Texas Instruments TMS320C6201 is a highly efficient digital signal processor. Ensure smooth functioning of your device by staying updated with the latest Errata Corrections. Download the comprehensive user manual for free from manualshive.com, providing step-by-step instructions, troubleshooting tips, and optimization techniques essential for harnessing the full potential of this powerful product.

Share
Download
background image

HPI Signal Descriptions

7-11

Host-Port Interface

Figure 7–5 shows the equivalent circuit of the HCS, HDS1, and HDS2 inputs.

Figure 7–5. Select Input Logic

HSTROBE (internal signal)

HDS2

HDS1

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁÁ

ÁÁÁÁ

HCS

Used together, HCS, HDS1, and HDS2 generate an active (low) internal
HSTROBE signal. HSTROBE is active (low) only when both HCS is active and
either (but not both) HDS1 or HDS2 is active. The falling edge of HSTROBE
when HAS is tied inactive (high) samples HCNTL[1:0], HHWIL, and HR/W.
Therefore, the latest of HDS1 , HDS2, or HCS controls the sampling time. HCS
serves as the enable input for the HPI and must be low during an access. How-
ever, because the HSTROBE signal determines the actual boundaries be-
tween accesses, HCS can stay low between successive accesses as long as
both HDS1 and HDS2 transition appropriately.

Hosts with separate read and write strobes connect these strobes to either
HDS1 or HDS2. Hosts with a single data strobe connect it to either HDS1 or
a HDS2, tying the unused pin high. Regardless of HDS1 and HDS2 connec-
tions, HR/W is required to determine the direction of transfer. Because HDS1
and HDS2 are internally exclusive-NORed, hosts with a high true data strobe
can connect this strobe to either HDS1 or HDS2 with the other signal tied low.

HSTROBE is used for four purposes:

-

On a read, the falling edge of HSTROBE initiates HPI read accesses for
all access types.

-

On a write, the rising edge of HSTROBE initiates HPI write accesses for
all access types.

-

The falling edge latches the HPI control inputs, including HHWIL, HR/W,
and HCNTL[1:0]. HAS also affects latching of control inputs. See section
7.2.8 for a description of HAS.

-

The rising edge of HSTROBE latches the HBE[1:0] input as well as the
data to be written.

HCS gates the HRDY output. In other words, a not-ready condition is indicated
by the HRDY pin being driven high only if HCS is active (low). Otherwise HRDY
is active (low).

Summary of Contents for TMS320C6201






























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for TMS320C6201

National Instruments NI 5922 Calibration Procedure preview
NI 5922
Brand: National Instruments Pages: 28
National Instruments NI 9219 Getting Started preview
NI 9219
Brand: National Instruments Pages: 19
National Instruments NI 6711 User Manual preview
NI 6711
Brand: National Instruments Pages: 103
National Instruments NI PXI-1042 Series Installation Manual preview
NI PXI-1042 Series
Brand: National Instruments Pages: 12
National Instruments PCI-1407 Setup And Operation preview
PCI-1407
Brand: National Instruments Pages: 4
Xilica Audio Design neutrino series Quick Start Manual preview
neutrino series
Brand: Xilica Audio Design Pages: 26
LSI MegaRAID SATA 300-4XLP Quick Installation Manual preview
MegaRAID SATA 300-4XLP
Brand: LSI Pages: 3
Aruba IntroSpect Analyzer 2 Series Quick Start Manual preview
IntroSpect Analyzer 2 Series
Brand: Aruba Pages: 5
Z3 Technology Z3-SBE264-10 User Instructions preview
Z3-SBE264-10
Brand: Z3 Technology Pages: 67
B&B Electronics 232PCC User Manual preview
232PCC
Brand: B&B Electronics Pages: 17
ekwb EK-FC750 GTX Series Installation Manual preview
EK-FC750 GTX Series
Brand: ekwb Pages: 2
JAKA MiniCab Hardware User Manual preview
MiniCab
Brand: JAKA Pages: 37
Renesas H8S/2646 Series User Manual preview
H8S/2646 Series
Brand: Renesas Pages: 20
ZALMAN CNPS20X User Manual preview
CNPS20X
Brand: ZALMAN Pages: 20
Z3 Technology DM8168-MOD-35 Manual preview
DM8168-MOD-35
Brand: Z3 Technology Pages: 22
Amphenol C2LINX Series Installation Manual preview
C2LINX Series
Brand: Amphenol Pages: 43
Ceragon Fibe-Air IP-10G Installation Manual preview
Fibe-Air IP-10G
Brand: Ceragon Pages: 71
Enterasys GPIM-08 Reference Sheet preview
GPIM-08
Brand: Enterasys Pages: 2

Brands by name

Popular brands

Load more brands