manualshive.com logo in svg

Texas Instruments TMS320C6201, Reference Manual

The Texas Instruments TMS320C6201 is a highly efficient digital signal processor. Ensure smooth functioning of your device by staying updated with the latest Errata Corrections. Download the comprehensive user manual for free from manualshive.com, providing step-by-step instructions, troubleshooting tips, and optimization techniques essential for harnessing the full potential of this powerful product.

Share
Download
background image

Designing Your Target System’s Emulator Connector (14-Pin Header)

15-3

Designing for JTAG Emulation

Although you can use other headers, recommended parts include:

straight header, unshrouded

DuPont Connector Systems
part numbers:

 65610–114

 65611–114

 67996–114

 67997–114

15.2 Bus Protocol

The IEEE 1149.1 specification covers the requirements for the test access port
(TAP) bus slave devices and provides certain rules, summarized as follows:

-

The TMS/TDI inputs are sampled on the rising edge of the TCK signal of
the device.

-

The TDO output is clocked from the falling edge of the TCK signal of the
device.

When these devices are daisy-chained together, the TDO of one device has
approximately a half TCK cycle setup to the next device’s TDI signal. This type
of timing scheme minimizes race conditions that would occur if both TDO and
TDI were timed from the same TCK edge. The penalty for this timing scheme
is a reduced TCK frequency.

The IEEE 1149.1 specification does not provide rules for bus master (emula-
tor) devices. Instead, it states that it expects a bus master to provide bus slave
compatible timings. The XDS510 provides timings that meet the bus slave
rules.

15.3 IEEE 1149.1 Standard

For more information concerning the IEEE 1149.1 standard, contact IEEE
Customer Service:

Address: IEEE Customer Service

445 Hoes Lane, PO Box 1331
Piscataway, NJ  08855-1331

Phone:

(800) 678–IEEE in the US and Canada
(908) 981–1393 outside the US and Canada

FAX:

(908) 981–9667         Telex:       833233

Designing Your Target System’s Emulator Connector (14-Pin Header) / Bus Protocol / IEEE 1149.1 Standard

Summary of Contents for TMS320C6201






























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for TMS320C6201

Vonets MINI300 Quick Setting Manual preview
MINI300
Brand: Vonets Pages: 8
Alesis QUADRAVERB Reference Manual preview
QUADRAVERB
Brand: Alesis Pages: 61
NEC Thin Client US310e Getting Started preview
Thin Client US310e
Brand: NEC Pages: 6
Lutron Electronics Smart Bridge Quick Start Manual preview
Smart Bridge
Brand: Lutron Electronics Pages: 4
Kontron CPS3003-SA User Manual preview
CPS3003-SA
Brand: Kontron Pages: 19
Atmel STK501 Specification Sheet preview
STK501
Brand: Atmel Pages: 2
mikroElektronika Pressure click Quick Start Manual preview
Pressure click
Brand: mikroElektronika Pages: 2
Commell FS-A79 User Manual preview
FS-A79
Brand: Commell Pages: 36
PairGain T1L2N20A Manual preview
T1L2N20A
Brand: PairGain Pages: 80
Xtreme SNMP-1PMINI User & Installation Manual preview
SNMP-1PMINI
Brand: Xtreme Pages: 83
Vacron VDH-NK300 Hardware Manual preview
VDH-NK300
Brand: Vacron Pages: 16
RAID N8103-134 Setup Manual preview
N8103-134
Brand: RAID Pages: 80
Areca ARC-12x4 Series Quick Installation Manual preview
ARC-12x4 Series
Brand: Areca Pages: 2
National Instruments PXI Express PXIe-1085 Series User Manual preview
PXI Express PXIe-1085 Series
Brand: National Instruments Pages: 89
StetSom STX2448 User Manual preview
STX2448
Brand: StetSom Pages: 18
JETWAY JNLH61S-6C Series User Manual preview
JNLH61S-6C Series
Brand: JETWAY Pages: 36
Patton electronics 593/25, 593/45, 593/TB, RS-422, RS-485 User Manual preview
593/25, 593/45, 593/TB, RS-422, RS-485
Brand: Patton electronics Pages: 8
Renesas RL78 Series User Manual preview
RL78 Series
Brand: Renesas Pages: 31

Brands by name

Popular brands

Load more brands