Terasic ALTERA DE4 User Manual Download Page 94

Page: 94 / 159

DE4 User Manual

www.terasic.com

June 20, 2018

This section will introduce the general design flow to build a project for the DE4 board via the DE4

System Builder. The general design flow is illustrated in the

Figure 4–1

Users should launch DE4 System Builder and create a new project according to their design

requirements. When users complete the settings, the DE4 System Builder will generate two major

files which include top-level design file (.v) and the Quartus II setting file (.qsf).

The top-level design file contains top-level verilog wrapper for users to add their own design/logic.

The Quartus II setting file contains information such as FPGA device type, top-level pin assignment,

and I/O standard for each user-defined I/O pin.

Finally, Quartus II programmer must be used to download SOF file to DE4 board using JTAG

interface.

Summary of Contents for ALTERA DE4
































































































































































Search results

Summary of Contents for ALTERA DE4

Reviews:

Related manuals for ALTERA DE4

Brands by name

Popular brands

Terasic ALTERA DE4, User Manual

Search results

Summary of Contents for ALTERA DE4

Reviews:

Related manuals for ALTERA DE4

Brands by name

Popular brands