Terasic ALTERA DE4 User Manual Download Page 132

Page: 132 / 159

DE4 User Manual

132

www.terasic.com

June 20, 2018

clock provided from the board. The DDR2 controller is configured as a 1Gbytes DDR2-800

controller. The DDR2 IP generates one 400 MHz clock as SDRAM’s data clock and one half-rate

system clock 200 MHz for those controllers, e.g. NIOS processor, accessing the SDRAM. In the

SOPC, NIOS and On-Chip Memory are designed running with the 200 MHz clock, and the other

controllers are designed running with 10 MHz clock which is generated by the PLL. The NIOS

program is running in the on-chip memory.

Figure 5

–22 Block diagram of the DDR2 demonstration

The system flow is controlled by a NIOS program. First, the NIOS program writes test patterns into

the whole 1GBytes SDRAM. Then, it calls NIOS system function, alt_dache_flush_all, to make

sure all data has been written to SDRAM. Finally, it reads data from SDRAM for data verification.

The program will show progress in JTAG-Terminal when writing/reading data to/from the SDRAM.

When verification process is completed, the result is displayed in the JTAG-Terminal.



Altera DDR2 SDRAM High Performance Controller

To use Altera DDR2 controller, users need to perform three major steps: 1). Create correct pin

assignment for DDR2. 2). Setup correct parameters in DDR2 controller dialog. 3). Execute TCL

files, generated by DDR2 IP, under your Quartus project.

The following section describes some of the import issues in support of the DDR2 controller

Summary of Contents for ALTERA DE4
































































































































































Search results

Summary of Contents for ALTERA DE4

Reviews:

Related manuals for ALTERA DE4

Brands by name

Popular brands

Terasic ALTERA DE4, User Manual

Search results

Summary of Contents for ALTERA DE4

Reviews:

Related manuals for ALTERA DE4

Brands by name

Popular brands