manualshive.com logo in svg

StarTech.com IES101002SFP, Instruction Manual

Share
Download
StarTech.com IES101002SFP Instruction Manual Download Page 66

Instruction Manual

58

Relay 

Information 

Policy

Indicates the DHCP relay information policy option. When DHCP 

relay information mode operation is enabled, if an agent receives 

a DHCP message that already contains relay agent information, 

it will enforce the policy. The Replace option is invalid when relay 

information mode is disabled. 
Possible policies are:

[Replace]

Replace the original replay information when a DHCP message 

that already contains it is received.

[Keep]

Keep the original relay information when a DHCP message that 

already contains it is received.

[Drop]

Drop the package when a DHCP message that already contains 

replay information is received.

1.  On the main screen of the Web management UI, click 

Configuration

 > 

Security

 > 

Network

 > 

DHCP 

> 

Relay

.

2.  Set the 

Relay Mode

 to either 

Enabled

 or 

Disabled

.

3.  Specify the

 Relay Server 

address.

4.  Set 

Relay Information Mode

 to either 

Enabled

 or 

Disabled

.

5.  Specify 

Policy Settings

.

6.  To save your settings, click 

Save

.

To restore the previous settings, click 

Reset

.

Summary of Contents for IES101002SFP



















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands