manualshive.com logo in svg

StarTech.com IES101002SFP, Instruction Manual

Share
Download
StarTech.com IES101002SFP Instruction Manual Download Page 148

Instruction Manual

140

Change the Port Status settings

Use the LACP Port Status screen to display information on the LACP groups active on 

each port.
You can access the screen by clicking 

Monitor

 > 

LACP 

> 

Port Status

.

Menu option

Description

Port LACP

Indicates the switch port number. 

Yes

 indicates that LACP is 

enabled and the port link is up. 

No

 indicates that LACP is not 

enabled or that the port link is down. 

Backup

 indicates that 

the port could not join the aggregation group but will join if 

other ports leave. Meanwhile its LACP status is disabled

Key

Indicates the key assigned to this port. Only ports with the 

same key can aggregate together.

Aggr ID

Indicates the Aggregation ID assigned to this aggregation 

group.

Partner System ID

Indicates the partner’s System ID (MAC address).

Partner Port

Indicates the partner’s port number connected to this port.

Partner Prio

Indicates the partner’s port priority.

Buttons

Auto-refresh: Select the Auto-refresh check box to 

automatically refresh the page at regular intervals.
Refresh: Updates the system log entries, starting from the 

current entry ID

1.  To display the LACP status for local ports, on the main screen of the Web 

management UI, click 

Monitor

 > 

LACP 

>

 Port Status

.

Summary of Contents for IES101002SFP



















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands