manualshive.com logo in svg

StarTech.com IES101002SFP, Instruction Manual

Share
Download
StarTech.com IES101002SFP Instruction Manual Download Page 35

Instruction Manual

27

Change the Log settings

The following table describes the Log settings that you can change:

Option

Description

Server Mode

Enable or disable remote system logging.

Server Address

Specify the IP address of the server used for remote system 

logging.

Syslog Level

Select one of the following logging event levels: Info, Warning, 

or Error.

1.  On the main screen of the Web management UI, click 

Configuration

 > 

System

 > 

Log

.

2.  Do one of the following:

• To enable Server mode, in the 

Server Mode

 drop-down list, click 

Enabled

.

• To disable Server mode, in the 

Server Mode

 drop-down list, click 

Disabled

.

3.  In the 

Server Address

 field, enter the IP address of the server.

4.  Do one of the following:

• To send info, warnings, and errors, in the 

Syslog Level

 drop-down list, click 

Info

.

• To send warnings and errors, in the 

Syslog Level

 drop-down list, click 

Warning

.

• To send errors, in the 

Syslog Level

 drop-down list, click 

Error

.

5.  To save your changes, click 

Save

.

To restore the previous settings, click 

Reset

.

Change the LED settings

The following table describes the LED settings that you can change to reduce the LED 

intensity during specified hours to save power.

Option

Description

Time

Specify the length of time to change the LED itensity for.

Intensity

Set the LED intensity percentage level. There are 10 levels of 

LED intensity, increasing by 10% intensity with each level. 0% 

intensity level means the LED is turned off and 100% intensity 

means the LED is at full power.

Summary of Contents for IES101002SFP



















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands