manualshive.com logo in svg

StarTech.com IES101002SFP, Instruction Manual

Share
Download
StarTech.com IES101002SFP Instruction Manual Download Page 128

Instruction Manual

120

Buttons

Auto-refresh: Select this check box to enable an automatic 

refresh of the page at regular intervals.
Refresh: Updates the system log entries, starting from the 

current entry ID.
Resolve Conflict: Flushes all of the system log entries.

1.  On the main screen of the Web management UI, click 

Monitor

 > 

Ports 

>

 Detailed 

Statistics

.

2.  Select a port number to display the detailed statistics for the port.

Change the ACL Status settings

Use the Access Management Statistics screen to monitor management traffic through 

five interfaces, including HTTP, HTTPS, SNMP, TELNET, and SSH.
You can access the screen by clicking 

Monitor

 > 

Ports 

> 

ACL Status

.

Menu option

Description

Interface

The interface type that the remote host can access the switch 

through.

Received Packets

The number of received packets from the interface when 

access management mode is enabled.

Allowed Packets

The number of allowed packets from the interface when 

access management mode is enabled.

Discarded Packets

The number of discarded packets from the interface when 

access management mode is enabled.

1.  On the main screen of the Web management UI, click 

Monitor

 > 

Security 

>

 Access 

Management Statistics

.

2.  To refresh the screen periodically, click 

Auto-refresh

.

Summary of Contents for IES101002SFP



















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands