manualshive.com logo in svg

StarTech.com IES101002SFP, Instruction Manual

Share
Download
StarTech.com IES101002SFP Instruction Manual Download Page 145

Instruction Manual

137

Change the RMON History settings

This screen provides an overview of RMON History entries.
You can access the screen by clicking 

Monitor

 > 

Security 

> 

Switch 

>

 RMON 

>

 History

.

Menu option

Description

History Index

Indicates the index of the history control entry.

Sample Index

Indicates the index of the data entry associated with the 

control entry.

Sample Start

Indicates the value of sysUPTime at the start of the interval 

over which this sample was measured.

Drop

Indicates the the total number of events in which packets 

were dropped by the probe due to lack of resources.

Octets

Indicates the total number of octets of data (including those 

in bad packets) received on the network.

Pks

Indicates the total number of packets (including bad packets, 

broadcast packets, and multicast packets) received.

Broad-cast

Indicates the total number of good packets received that were 

directed to the broadcast address.

Multi-cast

Indicates the total number of good packets received that were 

directed to a multicast address.

CRC Errors

Indicates the total number of packets received that had a 

length (excluding framing bits but including FCS octets) of 

64 to1518 octets inclusive, but had either a bad frame check 

sequence (FCS) with an integral number of octets (FCS Error) 

or a bad FCS with a non-integral number of octets (Alignment 

Error).

Under-size

Indicates the total number of packets received that were less 

than 64 octets.

Over-size

Indicates the total number of packets received that were 

longer than 1518 octets.

Frag.

Indicates the number of frames which size is less than 64 

octets received with an invalid CRC.

Summary of Contents for IES101002SFP



















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands