Soehnle Professional 3035 Manual Download

Page: 65 / 124

Load dynamic function keys from the SD card via external terminal software:

This allows the configurations to be loaded from the SD card from the file with the transferred name.

Format:

<KcccKfff>

where: ccc3-digit

command code 533

fffFILENAME .TXT (see above)

Example:

<K533KTEST.TXT>

5.18.7 Printing conditions

For Action A3, the printing conditions that can be used to program a dynamic function key are listed below:

1=Print key 1

2=<A> Auto imprint/data record once immediately

3=<B> Auto printout/data record once after weight change at stability

4=<C> Auto printout/data record after weight change at stability

5=<D> Auto printout/data record after weight change at stability above empty

6=<E> Auto printout/data record after weight change at stability above empty signal after enabling small

empty signal

7=<F> Send running

8=Enter key when entering Org A

9=Enter key when entering Org B

10=Enter key when entering Org C

11=Enter key when entering Org D

12=Plus key

13=Enter/call over key for manual input

14=Enter/cancellation key

15=Sum key (depending on settings)

16=Container key (container seal)

17=Enter/transfer key during initial weighing

18=Enter/transfer key for second weighing

19=enter/transfer key for single weighing

20=<H> Auto printout/data record once without weight change at stability

21=Scanning

22=Print key 2

23=Send continuously EDV unidirectional

24=Print item list

25=Enter key

26=Start mode (Dyn. switching)

27=measuring point changeover

32=<I> EDP data record automatically after standstill

36=any print-triggering function for dynamic F-key or EDP commands

37=any print-triggering function for dynamic F-key or EDP commands

38=any print-triggering function for dynamic F-key or EDP commands

39=any print-triggering function for dynamic F-key or EDP commands

40=any print-triggering function for dynamic F-key or EDP commands

41=any print-triggering function for dynamic F-key or EDP commands

42=CL key

45=Multiscan ready

Summary of Contents for 3035





























































































































Search results

Summary of Contents for 3035

Reviews:

Related manuals for 3035

Brands by name

Popular brands

Soehnle Professional 3035, Manual

Search results

Summary of Contents for 3035

Reviews:

Related manuals for 3035

Brands by name

Popular brands