Soehnle Professional 3035 Manual Download

Page: 109 / 124

109

Control status

Traffic light colour

Special characters

Below tolerance limit

Yellow

Within tolerance

Green

Setpoint reached exactly

Green

Above tolerance limit

Red

In the secondary display with the Control light setting, no symbols are displayed but only the colours in the

display field of the secondary display.

If a memory location has been activated from the contr. fix memory which contains a setpoint and tolerance

value, the control functions traffic light / symbols are automatically activated according to the settings.

Display setpoint and tolerance

The currently used setpoints can be queried with the key sequence and F3 Setpoint.

New setpoint

Existing setpoints are overwritten by a new setpoint entry

Stop checking

Deleting the saved setpoint terminates the check procedure and leads to the weight display.

Press F1 Setpoint, then press the key or directly using the key .

Check fixed values (Contr. Fix)

You can store up to 999 setpoints in a power-failure-proof database.

Each memory location has the following entries:

> Three-digit serial number

> Description (alphanumeric max. 18 characters)

> Article number (alphanumeric max. 18 digits)

> setpoint

> Tolerance minus

> Tolerance plus

a) Call up the list of fixed values control weights to edit the fixed values:

Press key and then F2 Contr.

Selection of existing fixed values from the list

Scroll with the arrow keys F3 or F4 until the desired memory location is reached, accept the desired fixed

value with F6 Edit.

Direct access via article number or memory location number. Enter the article number or memory location

number with the numeric keypad. Whether to call the item number or memory location number is specified in

the setting mode. Enter the article number as a search criterion left-justified and the memory location

number as a search criterion right-justified. Accept the desired fixed value with F6 Edit.

Summary of Contents for 3035





























































































































Search results

Summary of Contents for 3035

Reviews:

Related manuals for 3035

Brands by name

Popular brands

Soehnle Professional 3035, Manual

Search results

Summary of Contents for 3035

Reviews:

Related manuals for 3035

Brands by name

Popular brands