Soehnle Professional 3035 Manual Download

Page: 61 / 124

5.18 Dynamic function keys

The dynamic function keys enable the function keys F1 - F6 to be individually designed on a separate,

programmable level. Here, process-dependent function keys can be configured and used.

The dynamic function keys have the following characteristics:

are configured via computer commands

can be shown or hidden

the function key level is freely selectable

Function key texts are 1 or 2 lines

the function of the function key can be configured within a certain range

the function keys are independent of the set program

the properties of the keys are only defined via EDP commands!

the properties of the keys can be saved on the SD card.

5.18.1 Configuration commands

The following computer commands are available for configuring the dynamic function keys:

530Definition of

a dynamic function key

531Dynamic function keys - Line on -/off

532Level of dynamic function keys - define line

533Dynamic function keys - Save settings on SD card

534Dynamic function keys - Load settings from SD card

5.18.2 Defining a dynamic function key

Format:<KcccKFx

;nL;tttt;Aa;dddd>

Here is:

ccc3-digit

command code from point 3

xthe function key number for which the configuration is (x = 1 ... 6)

n is the number of lines in the function key field (n = 1 ... 2)

tttdthe function key text. It consists of a maximum of 7 characters per line.

For 2-line text, up to 14 characters at a time.

the action number. It defines the function to be performed.

dddddthe

data required for the action (max. 35 bytes).

actions:

The following actions are defined:

A0Delete function key definition

A1Send data via EDP channel, i.e. the data dddd defined for the corresponding function key

is sent transparently via the EDP interface.

A2Send data via EDP channel as EDP command, i.e. it corresponds to the above command,

with the data being sent as <dddd>.

Interpret A3 data

as a print command, i.e. the data (ASCII number) is interpreted and

processed as a print code.

Summary of Contents for 3035





























































































































Search results

Summary of Contents for 3035

Reviews:

Related manuals for 3035

Brands by name

Popular brands

Soehnle Professional 3035, Manual

Search results

Summary of Contents for 3035

Reviews:

Related manuals for 3035

Brands by name

Popular brands