Siemens SINAMICS S220 Equipment Manual Download Page 89 | Manualshive

Page: 89 / 156

Siemens SINAMICS S220 Equipment Manual Download Page 89

Fixing the cables to the rear cabinet panel
1. Fix the DC link connecting cables directly next to the last component at the rear control

cabinet panel. Use the C rails and the matching cable clamps from the Rittal company. The
distance between the C rail and the lower side of the component is approximately 125 mm.

2. Appropriately insulate the cable cores at the connection location before mounting.

①

Control cabinet panel

②

DC link adapter

③

Cores of the DC link connecting cable

④

C rail from the Rittal company (article number 7831.570 / 7831.571)

⑤

Cable clamps for C rails from the Rittal company

Figure 6-5

Mounting the DC link adapter (6SL3162-2BM01-0AA0), dimensions in mm and (inch)

Cable connection and shield support
In order to simplify installing the DC link connecting cables at the DC link adapter, first fix the
cables to the control cabinet panel (see diagram above).

Required tools:

• Size 6 Allen key to attach the cables

• Suitable tool for hose clamps, e.g. flat-bladed screwdriver

Accessories

6.1 DC link adapter

Booksize power units
Equipment Manual, 01/2022, 6SL3097-6AC30-0BP0

87

«
...
87
88
89
90
91
...
»

Summary of Contents for SINAMICS S220





























































































































































Reviews:

No comments