Siemens SINAMICS S220 Equipment Manual Download Page 124

Page: 124 / 156

Required tool:

• Torx screwdriver T10

1. Place the 24 V connectors on to the 24 V busbars.

2. Press the 24 V connectors down until they click into place.

3. If required, mount the 24 V terminal adapter to supply the 24 V DC. Tightening torque, 0.5

Nm (4.4 lbf in).

①

Mounted 24 V terminal adapter

②

Mounted 24 V connector

8.7.2

Mounting the 24 V terminal adapter

The 24 V terminal adapter is included in the scope of supply of the Smart Line Modules and can
be ordered as a spare part (article number: 6SL3162-2AA00-0AA0).

①

24 V terminal adapter

②

Screw: SHR, PT-TORX K30-3, 0X16-ST-A2F WN1452 / from EJ
Tightening torque: 0.5 Nm (4.4 lbf in)

Control cabinet design and EMC booksize
8.7 Electrical connection

Booksize power units

122

Equipment Manual, 01/2022, 6SL3097-6AC30-0BP0

Summary of Contents for SINAMICS S220





























































































































































Search results

Summary of Contents for SINAMICS S220

Reviews:

Siemens SINAMICS S220, Equipment Manual, Page: 124 / 156

Search results

Summary of Contents for SINAMICS S220

Reviews: