manualshive.com logo in svg

Siemens SINAMICS S220, Equipment Manual, Page: 119 / 156

Share
Download
Siemens SINAMICS S220 Equipment Manual Download Page 119

The components are normally used in machines. The assessment and testing is based on 
DIN EN 12198.

Table 8-4

Information for frequency range 0 Hz to 300 GHz

Frequency range

0 Hz ... 100 kHz

100 kHz ... 300 GHz

Electric field strength

Limits not exceeded

Limits not exceeded

Magnetic flux density

For assessment, see the following 
table

Limits not exceeded

Table 8-5

Minimum clearances to SINAMICS S220 power units at 0 Hz ... 100 kHz in cm (inch)

Power of the 
Line Module

Generally

Individuals with active implants

Control cabinet

closed

Control cabinet

open

Control cabinet

closed

Control cabinet

open

P ≤ 36 kW

0 (0)

10 (4)

The limit of 100 µT 
(RMS) at 50 Hz is not 
exceeded. Must be sep‐
arately assessed de‐
pending on the active 
implant.

Must be separately 
assessed depending 
on the active im‐
plant.

Note

The minimum distances indicated above apply to the head and complete torso of the human 
body. Shorter distances are possible for extremities.

Control cabinet design and EMC booksize

8.4 Electromagnetic fields at the workplace

Booksize power units
Equipment Manual, 01/2022, 6SL3097-6AC30-0BP0

117

Summary of Contents for SINAMICS S220





























































































































































Reviews:

No comments