manualshive.com logo in svg

Siemens SINAMICS S220, Equipment Manual, Page: 139 / 156

Share
Download
Siemens SINAMICS S220 Equipment Manual Download Page 139

For power cables from Siemens in which the shield is connected to the connector housing (see 
relevant catalog), this is a sufficiently good shield support.

• For components that do not have any special shield connection or where the shield 

connection is not adequate, you can connect the cable shields to the metal mounting plate 
using hose clamps and toothed rails. Keep the cable length between the shield connection 
point and the terminals for cable conductors as short as possible.

• For the 16 kW and 24 kW connecting cables of the S220 Smart Line Modules, it is permissible 

to connect the shield to the strain relief plate using a hose clamp. Alternatively, you can order 
an optional shield connection plate. More information is provided in Chapter "Shield 
connection plate and terminal (Page 96)".

• For S120 Line Modules and Active Interface Modules up to and including 16 kW - as well as 

for Motor Modules up to and including 30 A or 2x18 A - shield connection plates are either 
included in the scope of supply of the components or integrated in the connection plug. You 
must order shield connection plates for all other components. More information is provided 
in Chapters "Shield connection plates" and "Accessories" of the SINAMICS S120 Equipment 
Manual Booksize Power Units (

https://support.industry.siemens.com/cs/ww/en/view/

109781351

).

Routing 24 V conductors

When routing 24 V conductors, carefully observe the following additional requirements:

• A maximum of one conductor pair may be bundled together.

• You must route 24 V conductors separately away from other cables and conductors that may 

carry operational current.

• Never route 24 V conductors in parallel to power cables.

• You must route 24 V conductors and power cables to components so that they never cover 

the ventilation slots.

Conditions of use for 24 V conductors
• Ambient temperature: 55 °C

• Conductor limit temperature: ≤ 70 °C for operation with the rated load current

• Max. cable length: 30 m for 24 V conductors and for signal cables without additional circuitry

Overvoltage protection devices must be used for longer cable lengths.

Control cabinet design and EMC booksize

8.10 Cable shielding and routing

Booksize power units
Equipment Manual, 01/2022, 6SL3097-6AC30-0BP0

137

Summary of Contents for SINAMICS S220





























































































































































Reviews:

No comments