manualshive.com logo in svg

Siemens SINAMICS S220, Equipment Manual, Page: 134 / 156

Share
Download
Siemens SINAMICS S220 Equipment Manual Download Page 134

8.9

Connection system

8.9.1

Conditions for UL applications

Note
Conditions for UL applications
• Only use copper cables rated for 75 °C.
• For line and motor connections, only use UL-approved ring cable lugs (ZMVV) that are 

certified for the particular voltage. The permissible current-carrying capacity of the cable 
(routing type B2) must be at least 125 % of the input or output current.

8.9.2

DRIVE-CLiQ signal cables and MOTION-CONNECT power cables

DRIVE-CLiQ signal cable

The various options for connecting a direct measuring system with DRIVE-CLiQ and M12 plug via 
MOTION-CONNECT cables to a DRIVE-CLiQ component are described in Chapter "Connection 
system" of the SINAMICS S120 Equipment Manual Booksize Power Units (

https://

support.industry.siemens.com/cs/ww/en/view/109781351

).

8.9.3

Current-carrying capacity and derating factors for power cables and signal 
cables

The current-carrying capacity of PVC/PUR-insulated copper cables is specified for routing types 
B1, B2 and C under continuous operating conditions in the table below with reference to an 
ambient air temperature of 40°C. You must calculate the current-carrying capacity for deviating 
ambient temperatures. To do this, use the derating factor listed in the table below.

Table 8-13

Routing types

B1

Cables in conduits or cable ducts

B2

Multi-conductor cables in conduits or cable ducts

C

Cables along walls, without conduits or cable ducts

Control cabinet design and EMC booksize
8.9 Connection system

Booksize power units

132

Equipment Manual, 01/2022, 6SL3097-6AC30-0BP0

Summary of Contents for SINAMICS S220





























































































































































Reviews:

No comments