manualshive.com logo in svg

Siemens SINAMICS S220, Equipment Manual, Page: 121 / 156

Share
Download
Siemens SINAMICS S220 Equipment Manual Download Page 121

8.6

Single and multi-tier drive lineup

Single-tier drive lineup

Due to the current-carrying capacity of the DC link busbars and their function in particular, the 
components should be arranged according to the following rule.

From left to right:

• Line Modules

• Motor Modules in order of power from the highest power to the lowest power

• DC link components, e.g. Braking Module, Control Supply Module, Capacitor Module

More information is provided in Chapter "Arrangement of the components and units" of the 
SINAMICS S120 Equipment Manual Booksize Power Units (

https://

support.industry.siemens.com/cs/ww/en/view/109781351

).

Multi-tier drive lineup

Additional information on the design of a multi-tier drive lineup is provided in Chapter 
"Arrangement of the components and units" of the SINAMICS S120 Equipment Manual Booksize 
Power Units (

https://support.industry.siemens.com/cs/ww/en/view/109781351

).

Control cabinet design and EMC booksize

8.6 Single and multi-tier drive lineup

Booksize power units
Equipment Manual, 01/2022, 6SL3097-6AC30-0BP0

119

Summary of Contents for SINAMICS S220





























































































































































Reviews:

No comments