Siemens SINAMICS S220 Equipment Manual Download Page 43

Page: 43 / 156

• Ensure that the loop impedance complies with local installation regulations.

• Check the total length of the shielded power cables (motor cables incl. line supply cables

from line filters to the connection terminals of the Line Module) in the drive lineup. The total
length must be less than 350 m.

• Only operate the system with the recommended line filters.

• Ensure that the switching elements (disconnector unit, contactors) for connecting and

disconnecting the drive system have a delay time of max. 35 ms between the closing/
opening of the individual main contacts.

Note
Nuisance tripping of RCDs

In case of unfavorable line supply conditions, as a result of the system that they are being used
in, converters can generate capacitive leakage currents that can cause RCDs to nuisance trip.

4.3.2

Residual current circuit breakers (RCCB)

0QUJPOBM

'VTFT

-JOFDPOUBDUPS

PQUJPOBM

-JOF꫼MUFS

-JOFSFBDUPS

6HOHFWLYH

$&'&VHQVLWLYH

UHVLGXDOFXUUHQWRSHUDWHG

FLUFXLWEUHDNHU

"EEJUJPOBM

MPBET

-JOF.PEVMF

'&1

'&3

8 9 :

Figure 4-2

Connection of a residual-current protective device

Line connection and line-side power components

4.3 Connected to the line supply via residual current devices (RCD)

Booksize power units
Equipment Manual, 01/2022, 6SL3097-6AC30-0BP0

Summary of Contents for SINAMICS S220





























































































































































Search results

Summary of Contents for SINAMICS S220

Reviews:

Siemens SINAMICS S220, Equipment Manual, Page: 43 / 156

Search results

Summary of Contents for SINAMICS S220

Reviews: