manualshive.com logo in svg

Siemens SINAMICS S220, Equipment Manual, Page: 102 / 156

Share
Download
Siemens SINAMICS S220 Equipment Manual Download Page 102

6.3

 DRIVE-CLiQ cabinet bushings and coupling

DRIVE-CLiQ cabinet bushing 

A DRIVE-CLiQ cabinet bushing is used to connect the DRIVE-CLiQ cables between the inside and 
outside of the control cabinet. It is used in a control cabinet panel. The data cables and the power 
supply contacts of the DRIVE-CLiQ are also routed through the bushing. The DRIVE-CLiQ cabinet 
bushing is available for DRIVE-CLiQ cables with RJ45 plug and M12 plug/socket.

Additional information is provided in Chapter "Accessories" of the SINAMICS S120 Equipment 
Manual Booksize Power Units (

https://support.industry.siemens.com/cs/ww/en/view/

109781351

).

DRIVE-CLiQ coupling 

The DRIVE-CLiQ coupling is used to connect 2 DRIVE-CLiQ cables in accordance with degree of 
protection IP67 acc. to IEC 60529.

Additional information is provided in Chapter "Accessories" of the SINAMICS S120 Equipment 
Manual Booksize Power Units (

https://support.industry.siemens.com/cs/ww/en/view/

109781351

).

Accessories
6.3  DRIVE-CLiQ cabinet bushings and coupling

Booksize power units

100

Equipment Manual, 01/2022, 6SL3097-6AC30-0BP0

Summary of Contents for SINAMICS S220





























































































































































Reviews:

No comments