Siemens SINAMICS S220 Equipment Manual Download Page 143

Page: 143 / 156

Humidity

NOTICE
Component damage caused by condensation

Condensation on the components can cause them to fail.
• Select the air circuit and arrangement of the cooling equipment in such a way that no

condensation can form on the components.

• If required, an anti-condensation heater must be installed in the cabinet.

When using air-conditioning units, the relative humidity of the air that is discharged can increase
as a result of the air being cooled in the air-conditioning unit. Under certain circumstances, the
humidity can exceed the dew point.

• To avoid condensation, arrange the air-conditioning units so that cold discharged air is not

directly blown onto the components.

• If required, use air guidance baffles to ensure that the air is adequately mixed with the air

inside the control cabinet. Mixing with warm air reduces the relative humidity down to
uncritical values.

8.12.2

Ventilation clearances

Table 8-20

Ventilation clearances above and below components

Component

Minimum clearance [mm]

Line filters for Smart Line Modules

100

Line reactors for Smart Line Modules

100

Smart Line Modules

Control cabinet design and EMC booksize

8.12 Control cabinet cooling

Booksize power units
Equipment Manual, 01/2022, 6SL3097-6AC30-0BP0

141

Summary of Contents for SINAMICS S220





























































































































































Search results

Summary of Contents for SINAMICS S220

Reviews:

Siemens SINAMICS S220, Equipment Manual, Page: 143 / 156

Search results

Summary of Contents for SINAMICS S220

Reviews: