Siemens SINAMICS S220 Equipment Manual Download Page 30 | Manualshive

Page: 30 / 156

Siemens SINAMICS S220 Equipment Manual Download Page 30

3.2

Intended use

Description

The products described in this manual, together with software, accessories, and options, form
an electrical power drive system intended to feed low-voltage AC motors. The products are
intended for use in industrial applications. The products must be installed and maintained by
professionals with sufficient knowledge to implement the safety and EMC measures according
to the specifications described in this manual and the recognized state ofthe art.

You may only use the products in compliance with the following requirements:

• All regulations and directives that are applicable at the site of the end use, especially with

regard to electrical safety, functional safety and electromagnetic compatibility.

• All instructions, notes, technical data and safety information contained in this manual and

other supporting documentation.

Before using the products, you must perform a risk assessment of the entire application and
implement appropriate system design measures to ensure safety of persons, property and
electromagnetic compatibility.

Open type products (IP00/IP20) are intended for incorporation within cubicles or enclosures
which will provide necessary protection.

Any use other than the use explicitly permitted is prohibited and can result in unanticipated
hazards.

System overview
3.2 Intended use

Booksize power units

28

Equipment Manual, 01/2022, 6SL3097-6AC30-0BP0

«
...
28
29
30
31
32
...
»

Summary of Contents for SINAMICS S220





























































































































































Reviews:

No comments