manualshive.com logo in svg

Siemens SINAMICS S220, Equipment Manual, Page: 151 / 156

Share
Download
Siemens SINAMICS S220 Equipment Manual Download Page 151

9.3

Forming the DC link capacitors

Overview

DC link capacitors must be reformed for Line Modules that have been in storage for more than 
2 years. If this is not performed, the components could be damaged when they are switched on.

Requirement

DC link capacitors of components for which the storage period of 2 years has been exceeded 
must be reformed.

• The storage period is calculated from the date of manufacture and not from the date that the 

equipment was shipped.

• Refer to the serial number on the rating plate for the date of manufacture.

Made in Germany



①

Designation

②

Article number

③

Year of manufacture (here O = 2022) and month of manufacture (here 2 = February)

Figure 9-1

Rating plate (example: Smart Line Module 16 kW)

Table 9-2

Year and month of manufacture on the rating plate

Year of manufacture

Month of manufacture

Character

Year

Character

Month

O

2022

1 ... 9

January to September

P

2023

O

October

Q

2024

N

November

R

2025

D

December

S

2026

 

 

Service and maintenance

9.3 Forming the DC link capacitors

Booksize power units
Equipment Manual, 01/2022, 6SL3097-6AC30-0BP0

149

Summary of Contents for SINAMICS S220





























































































































































Reviews:

No comments