Siemens SIMOTION P320-3 Page 97 Manual Download

Page: 97 / 150

Connecting

6.5 Protective ground connection

SIMOTION P320-3 and Panel Fronts
Manual, 02/2012

6.5

Protective ground connection

Device safety

The PE terminal is needed to protect the device and ensures that interference signals

generated by external power cables, signal cables or cables to the I/O modules are safely

discharged to ground.

Required tools

Required tool for protective earth terminal: TORX T20 screwdriver

Procedure

Connect the PE terminal (M4 thread)

①

on the device (large contact surface) to the PE

conductor on the cabinet or system in which the PC will be installed. The minimum conductor

cross-section may not be less than 5 mm

Figure 6-3

Connecting the protective earth

Summary of Contents for SIMOTION P320-3























































































































































Search results

Summary of Contents for SIMOTION P320-3

Reviews:

Related manuals for SIMOTION P320-3

Brands by name

Popular brands

Siemens SIMOTION P320-3, Manual

Search results

Summary of Contents for SIMOTION P320-3

Reviews:

Related manuals for SIMOTION P320-3

Brands by name

Popular brands