Siemens SIMOTION P320-3 Manual Download

Page: 59 / 150

Hardware description

3.5 SIMOTION panel fronts

SIMOTION P320-3 and Panel Fronts
Manual, 02/2012

Note
When using standard USB peripheral devices, please bear in mind that their EMC immunity

level is frequently designed for office applications only.
Such devices are suitable for commissioning and servicing purposes; however, industrial

components are recommended for normal operation in industrial environments.

NOTICE

IP65 degree of protection can no longer be guaranteed for an externally connected USB

device. You can only assume a degree of protection IP20. This also applies if the rubber

seal on the front-mounted USB interface is damaged or missing.

Rear-mounted interfaces

The SIMOTION panel fronts are usually supplied with an additional metal plate containing

three cutouts for cable routing. The two ribbon cables used to connect the remote module

(distributed configuration) as well as the USB cable, have to be connected to the interfaces

on the remote module (see SIMOTION P320-3 and Panel Fronts Commissioning and

Hardware Installation Manual). Removing this metal plate reveals the rear side of the panel

front as shown in the figure.
● The USB I/O cable K1 at X1 is for all signals responsible for the connection of control

units in addition to the display interface.

● Display cable K2
● USB cable

'LVSOD\FDEOH

,286%FDEOH

86%FDEOH

WRS

Figure 3-13 Interfaces on rear side of panel

Summary of Contents for SIMOTION P320-3























































































































































Search results

Summary of Contents for SIMOTION P320-3

Reviews:

Related manuals for SIMOTION P320-3

Brands by name

Popular brands

Siemens SIMOTION P320-3, Manual

Search results

Summary of Contents for SIMOTION P320-3

Reviews:

Related manuals for SIMOTION P320-3

Brands by name

Popular brands