Siemens SIMOTION P320-3 Page 80 Manual Download

Page: 80 / 150

Installing/Mounting

5.2 Installing/removing an accessible CompactFlash card

SIMOTION P320-3 and Panel Fronts

Manual, 02/2012

5.2

Installing/removing an accessible CompactFlash card

Memory expansion options

The device features an accessible slot for CompactFlash cards (types I / II).
Only use SIMATIC PC CompactFlash cards for industrial application.

CAUTION

Replace the CompactFlash card only with a card of the same product version.
Only SIMATIC PC CompactFlash cards with product version 02 (ES 02) can be used for

this device.

Figure 5-1

SIMATIC PC CompactFlash

Figure 5-2

SIMATIC PC CompactFlash 4 GB - rear side with product version ES 02

Preparation

CAUTION

Data loss is possible on the CompactFlash card
Insertion/withdrawal of the CompactFlash card (CF card) while the device is switched on

can result in data loss on the CF card.
Exit the running software applications via the menu Start > Shut down, switch the device off

via the ON/OFF switch and disconnect the device from the power supply.

Summary of Contents for SIMOTION P320-3























































































































































Search results

Summary of Contents for SIMOTION P320-3

Reviews:

Related manuals for SIMOTION P320-3

Brands by name

Popular brands

Siemens SIMOTION P320-3, Manual

Search results

Summary of Contents for SIMOTION P320-3

Reviews:

Related manuals for SIMOTION P320-3

Brands by name

Popular brands