Siemens SIMOTION P320-3 Manual Download

Page: 73 / 150

Application planning

4.4 Mounting positions and fastening

SIMOTION P320-3 and Panel Fronts
Manual, 02/2012

Mounting position

Permitted temperatures / notes

Book mounting

0 to +45° C
See Section Upright mounting (Page 79)

RAL = Restricted Access Location

(installation of the device in operating facilities with restricted access - for example, a locked
control cabinet)

4.4.1

Permissible mounting positions of the panel front

Approval

Certain mounting positions are permitted for the SIMOTION panel fronts.

Permissible mounting positions for the SIMOTION panel front

Figure 4-2

Permissible mounting position of the panel front

Vertical installation and deviations of up to +20° and -20° in the given directions is

permissible.

Note
The mounting position illustrated has been tested and approved.

In the event of deviations from it, you might need to have additional tests carried out to verify

compliance with the general conditions applicable for the components used

(e.g. temperature). Siemens can provide appropriate support on request.

Summary of Contents for SIMOTION P320-3























































































































































Search results

Summary of Contents for SIMOTION P320-3

Reviews:

Related manuals for SIMOTION P320-3

Brands by name

Popular brands

Siemens SIMOTION P320-3, Manual

Search results

Summary of Contents for SIMOTION P320-3

Reviews:

Related manuals for SIMOTION P320-3

Brands by name

Popular brands