Siemens SIMOTION P320-3 Manual Download

Page: 28 / 150

Description

2.3 HMI and SIMOTION SCOUT

SIMOTION P320-3 and Panel Fronts

Manual, 02/2012

2.3.4

HMI or ES via PROFINET

PROFINET is the innovative and open Industrial Ethernet standard (EN 61158) for industrial

automation. With PROFINET, devices can be linked up from the field level through to the

management level.
If a PROFINET network is established, an external HMI/ES that supports PROFINET can

also be integrated into this network and exchange data directly with the SIMOTION device.

3HULSKHUDOV
'ULYHV

6,027,213

352),1(7

+0,(6

352),1(7,2

6,027,213

352),1(7,2

Figure 2-6

Model: Networking via PROFINET

This communication does not require any settings to be made for the SIMOTION P320-3.
These are made on the central HMI/ES as described in the documentation or online help for

SIMOTION SCOUT.

Summary of Contents for SIMOTION P320-3























































































































































Search results

Summary of Contents for SIMOTION P320-3

Reviews:

Related manuals for SIMOTION P320-3

Brands by name

Popular brands

Siemens SIMOTION P320-3, Manual

Search results

Summary of Contents for SIMOTION P320-3

Reviews:

Related manuals for SIMOTION P320-3

Brands by name

Popular brands