Siemens SIMOTION P320-3 Manual Download

Page: 51 / 150

Hardware description

3.4 SIMOTION P state application

SIMOTION P320-3 and Panel Fronts
Manual, 02/2012

3.4.4

Current operating status

The current status of your SIMOTION P is indicated on the left-hand side of the

SIMOTION P state window.
The following statuses can be indicated on the display:

"not started"

SIMOTION P is not started.

"0" … "5"

Individual stages during SIMOTION P booting.

"6 Running"

SIMOTION P has completed power up and the cyclic tasks are activated.

Figure 3-4

SIMOTION P state status display

The status LEDs and the current operating status are also displayed in the Windows task

bar.

Table 3- 8

Display in the task bar

RUN status: Green

STOP status: Yellow

NOT STARTED status: Gray

Summary of Contents for SIMOTION P320-3























































































































































Search results

Summary of Contents for SIMOTION P320-3

Reviews:

Related manuals for SIMOTION P320-3

Brands by name

Popular brands

Siemens SIMOTION P320-3, Manual

Search results

Summary of Contents for SIMOTION P320-3

Reviews:

Related manuals for SIMOTION P320-3

Brands by name

Popular brands