Siemens SIMOTION P320-3 Manual Download

Page: 74 / 150

Application planning

4.4 Mounting positions and fastening

SIMOTION P320-3 and Panel Fronts

Manual, 02/2012

4.4.2

Type of fixation

The control unit is secured in the mounting cut-out either with clamps or screws.

NOTICE

Securing with screws is not possible with the 12" touch screen variant.

Select the mounting type suitable for your requirements for the degree of protection.

4.4.3

Degree of protection

Principles

The degree of protection provided by the front side can only be guaranteed when the

mounting seal lies completely against the mounting cutout.

CAUTION

Please ensure that the material strength at the mounting cutout does not exceed 6 mm.

Please follow the specifications for the dimensions, seePanel front dimensions (Page 122)

and SIMOTION panel fronts installation dimensions (Page 123).
The degrees of protection are only guaranteed when the following is observed:



The material strength at the mounting cutout is at least 2 mm.



The deviation of the evenness of the mounting cutout with an HMI device installed is

≤ 0.5 mm relative to the outside dimensions of the HMI device.

Degree of protection IP65

The IP65 degree of protection is only provided for a clamp mounting together with a ring

seal.

Degree of protection IP54

This degree of protection is provided for screw mounting.

Summary of Contents for SIMOTION P320-3























































































































































Search results

Summary of Contents for SIMOTION P320-3

Reviews:

Related manuals for SIMOTION P320-3

Brands by name

Popular brands

Siemens SIMOTION P320-3, Manual

Search results

Summary of Contents for SIMOTION P320-3

Reviews:

Related manuals for SIMOTION P320-3

Brands by name

Popular brands