Siemens SIMOTION P320-3 Manual Download

Page: 102 / 150

Service and maintenance

7.2 Replace the backup battery

SIMOTION P320-3 and Panel Fronts

102

Manual, 02/2012

Battery warning

The 3 V lithium battery to back up the SRAM and the clock module is monitored in two

stages:

Battery voltage

Message

2.7 V ±0.1 V

Diagnostic buffer entry: Battery warning
Battery warning threshold reached

2.25 V ±0.25 V

Diagnostic buffer entry: Battery failure
Voltage below limit

In order to prevent data being lost, the battery should be replaced once the "Battery warning"

entry appears in the diagnostic buffer or, at the very latest, the first time the "Battery error"

entry appears in the diagnostic buffer.

Disposal

CAUTION

Batteries must be disposed of in accordance with local regulations.

Preparation

Note
The configuration data and contents of the SRAM in the device are buffered for at least 30

seconds.

Preparation – note the BIOS settings

Note
For the BIOS setting "Profile: Standard", the configuration data of the device will be deleted

when the battery is replaced.

For the BIOS setting "Profile: User", the configuration data of the device will be retained; only

the date and time needs to be reconfigured.

If necessary, note any specific BIOS setup settings if changes have been made.

Isolate the device from the power supply and disconnect all connecting cables.

Summary of Contents for SIMOTION P320-3























































































































































Search results

Summary of Contents for SIMOTION P320-3

Reviews:

Related manuals for SIMOTION P320-3

Brands by name

Popular brands

Siemens SIMOTION P320-3, Manual

Search results

Summary of Contents for SIMOTION P320-3

Reviews:

Related manuals for SIMOTION P320-3

Brands by name

Popular brands