Siemens SIMOTION P320-3 Manual Download

Page: 20 / 150

Description

2.1 Field of application

SIMOTION P320-3 and Panel Fronts

Manual, 02/2012

Individual automation tasks for production machines are formulated in a uniform and

consistent user interface. Logic and movement functions are programmed in the SIMOTION

SCOUT graphic programming tool.
Technical tasks such as positioning or synchronous operation are available as functions that

are simple to incorporate in the program, as are logic commands.
Consistency in the areas of programming and project design and data management and

communication is the central feature of Totally Integrated Automation (TIA).

SIMOTION P system architecture

The three hardware platforms (SIMOTION D, SIMOTION P and SIMOTION C) form the

basis of the SIMOTION motion control system. The application created with the SIMOTION

SCOUT engineering system and the associated runtime software modules can be used on

the various SIMOTION hardware platforms.
The advantage of the system architecture for the PC-based SIMOTION P320-3 solution lies

in the fact that both the HMI and the runtime system run on the same hardware. This saves

the cost for an additional HMI station.

Summary of Contents for SIMOTION P320-3























































































































































Search results

Summary of Contents for SIMOTION P320-3

Reviews:

Related manuals for SIMOTION P320-3

Brands by name

Popular brands

Siemens SIMOTION P320-3, Manual

Search results

Summary of Contents for SIMOTION P320-3

Reviews:

Related manuals for SIMOTION P320-3

Brands by name

Popular brands