Siemens SIMOTION P320-3 Page 81 Manual Download

Page: 81 / 150

Installing/Mounting

5.2 Installing/removing an accessible CompactFlash card

SIMOTION P320-3 and Panel Fronts
Manual, 02/2012

Note
The device is delivered with deactivated EWF (Enhanced Write Filter).
After commissioning the device, activate the EWF for drive C; this ensures the following:



An extended service life for the CF card



No data loss when switching the device off via the line side switch or through

disconnection from the power supply

CAUTION

The electronic components on the PCBs are highly sensitive to electrostatic discharge.

Always take appropriate precautionary measures when handling these components. Refer

to the directives for handling components that are sensitive to electrostatic charge. ESD

guidelines (Page 141).

Opening the module receptacle

To open the module receptacle, turn the
cover plate

①

of the module receptacle

180 degrees counter-clockwise.

Summary of Contents for SIMOTION P320-3























































































































































Search results

Summary of Contents for SIMOTION P320-3

Reviews:

Related manuals for SIMOTION P320-3

Brands by name

Popular brands

Siemens SIMOTION P320-3, Manual

Search results

Summary of Contents for SIMOTION P320-3

Reviews:

Related manuals for SIMOTION P320-3

Brands by name

Popular brands